Fundamental Plumbing Guide for Installing a Bathtub
Fundamental Plumbing Guide for Installing a Bathtub
Blog Article
This post following next in relation to A Step-by-Step Guide to Installing a Bathtub is indeed compelling. You should take a peek.
Mounting a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a new one is additionally a reasonably difficult job. If the old tub is readily obtainable, the job can move speedily; if you need to open up a wall to get rid of the old bathtub and position the brand-new tub, the job is a lot harder. In either case, the job is within a house handyman's skills, although you will need a helper to leave the old bathtub and set in the new one. Make sure you have actually qualified yourself for the work and also are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed task, it is better to consider utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will help you install a brand-new bathtub in your shower room if you have already acquired a new bathtub and also do not need to transform the plan of your previous water supply pipes.
Your devices and also material checklist need to consist of the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be fairly problematic due to the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel all set for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and also the sink. Protect the faucet in place with the producer given backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The former type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Using both wooden boards under its feet, place the tub in the required placement. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to make certain that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub until the level reviews degree.
To install faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other tap.
Activate the water system and inspect all joints and also brand-new pipework for leakages and also tighten them if needed. Fill the bathtub and likewise inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Lastly, fix the bath paneling as described in the maker's instruction manual. Tiling and also securing around the tub needs to wait till the bathtub has actually been utilized a minimum of when as this will settle it right into its final setting.
Planning for the Setup
Firstly, the supporting frame provided with the bath should be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent stress on the bath tub.
Fit the adaptable tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, creating the water to pass through the wall surface between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can split rather early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that editorial about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on our other website. Enjoyed our piece? Please share it. Let other people check it out. I love reading our article about How to Install a Bathtub.
Service excellence here. Report this page